ZHENGZHOU SHENGHONG HEAVY INDUSTRY TECHNOLOGY CO., LTD. sales@gcfertilizergranulator.com 86--15286833220
A disk type fertilizer factory is a granulation plant built around a rotating inclined pan, or disc granulator. Powder raw material is fed onto the pan together with water and a binder, and the tumbling action rolls the powder into round balls. Because the pan is open and visible from the operator platform, ball growth can be watched and corrected in real time. That is why disc granulation remains the most popular choice for small and medium compound and organic fertilizer plants: low capital cost, low power draw, quick model change and very simple maintenance.
A complete factory is more than a single machine. The granulator is the heart, but material preparation, drying, cooling, screening, coating and packing decide whether the plant can run stable output at a consistent granule size. This guide covers the equipment list, capacity planning, layout and operating rules for a disk type fertilizer factory.
Disc capacity is driven mainly by pan diameter. The four standard models below are the sizes used in most export projects, and all of them share the same adjustable disc angle of 45 to 55 degrees and a 93 percent ball shape rate.
| Model | Capacity | Disc diameter | Motor power | Output granule size | Total weight |
|---|---|---|---|---|---|
| SHQ-1500 | 1-2 t/h | 1500 mm | 7.5 kW | 1-4 mm | 1.6 t |
| SHQ-2000 | 2-3 t/h | 2000 mm | 11 kW | 1-4 mm | 2.2 t |
| SHQ-2500 | 3-4 t/h | 2500 mm | 15 kW | 2-5 mm | 3.1 t |
| SHQ-3000 | 4-6 t/h | 3000 mm | 18.5 kW | 2-5 mm | 4.0 t |
A practical rule when sizing the line: pick the disc so that the granulator runs at 70 to 80 percent of its rated capacity. Dryer, cooler and screener are then sized to the granulator output, not to the peak of a single machine. Pan granulators are often installed in parallel, two or three units feeding one dryer, which keeps investment low and allows maintenance without a full stop.
Feed moisture for wet disc granulation is normally 18 to 25 percent. The granules leave the pan at roughly 30 to 40 percent moisture, which is why a dryer is mandatory for bagged product. If the raw material is already dry powder, water and binder are added at the pan rather than upstream.
The pan angle controls retention time. A steeper angle lets material leave faster and produces smaller balls; a flatter angle keeps material longer and grows larger balls. The 45 to 55 degree adjustment range covers most compound and organic recipes without changing any part.
Spray water as a fine mist, never as a stream. Start at low flow, increase gradually and watch ball formation on the pan. Overspray creates mud and agglomerates, underspray creates dust and fines. For organic material with high fiber content, a small amount of binder helps the nucleus form.
Screened fines are returned to the pan as nuclei. A stable recycle ratio keeps the ball size distribution narrow and reduces binder consumption. Track the recycle tonnage daily; a sudden rise usually means the pan angle or moisture has drifted.
Cost in a disk type fertilizer factory is split into four blocks: preparation equipment, the granulation section, the drying and cooling section, and packing and dust control. The dryer usually takes the largest share because it is sized to evaporate water, so every point of moisture reduction achieved in the mixer or by better raw material storage pays back twice. Buildings, foundations, power connection and labour are local costs and should be quoted separately from the machine supply.
Yes. The machine is a wet type granulator and handles fermented manure powder, compost, humus as well as blended NPK powder. The binder type and water ratio change with the recipe, and the pan angle is adjusted on site.
The SHQ-1500 and SHQ-2000 models are typically set for 1 to 4 mm, and the larger SHQ-2500 and SHQ-3000 for 2 to 5 mm. Final sizing is confirmed by the screener, and the pan angle fine tunes the cut.
Minimum order is one set and lead time is about 15 working days after deposit. Machines ship in export-grade wooden cases or loaded in containers, with wear parts packed separately.
Tell us your raw material, target capacity per hour and the granule size you sell, and we will confirm the disc model, motor power, dryer size and the full layout within 24 hours. Shenghong Heavy Industry Technology Co., Ltd. has built fertilizer equipment in Zhengzhou, China since 2003, holds ISO 9001 and CE, and exports to more than 60 countries.