ZHENGZHOU SHENGHONG HEAVY INDUSTRY TECHNOLOGY CO., LTD. sales@gcfertilizergranulator.com 86--15286833220
A pan type granulation plant is not a single machine bolted to a frame. It is a sequence of stations where a rotating disc pan sits in the middle of the flow: raw material preparation comes before it, and drying, cooling, screening and packing come after it. Buyers who treat the disc granulator as the whole plant usually end up with wet, sticky granules and a screening room full of fines, because the disc shapes the ball but the rest of the line fixes the ball.
This article walks through the stations, the numbers that matter when you size a pan type granulation plant, and the decisions that decide whether the line runs at its rated capacity or drifts below it.
| Station | Function | Typical check before purchase |
|---|---|---|
| Crushing | Reduce composted or dried raw material to a powder that can be wetted evenly | Outlet fineness and dust control |
| Mixing | Blend powder with binder or water to a uniform moisture | Mixing time and discharge evenness |
| Disc granulation | Roll powder into ball shape granules on an inclined rotating pan | Disc diameter, pan angle range, motor power |
| Drying and cooling | Bring granule moisture down to a storage-safe level and cool the bed | Air temperature window, drum length to capacity ratio |
| Screening | Split product, recycle and fines into three streams | Mesh size and recycle ratio |
| Coating and packing | Add anti-caking film and bag the finished product | Bag weight accuracy and dust extraction |
Inside a pan type granulation plant, granulation is a wet process. Powder and water are fed onto an inclined pan that rotates at a fixed speed. Material rolls, grows, and climbs the rim of the pan; when a granule reaches its release size it rolls out over the edge of the pan and leaves the machine as a ball shape product. The pan angle controls how long material stays on the pan, and therefore how large the ball grows.
On the SHQ disc pan granulator range, the disc angle is adjustable between 45 and 55 degrees, feed material moisture is normally 18 to 25 percent, and discharge moisture after granulation runs about 30 to 40 percent. Ball shape rate is quoted at 93 percent, which is the figure that drives the recycle load on the screening deck: the higher the shape rate, the smaller the stream you have to send back to the mixer.
Capacity is set by pan diameter, not by motor size alone. The four standard models below cover 1 to 6 tons per hour; below that range, a smaller disc and a single screening deck keep the plant affordable, and above it the plant normally moves to a rotary drum granulator or a second disc running in parallel.
| Model | Capacity | Disc diameter | Motor power | Output granule size | Weight |
|---|---|---|---|---|---|
| SHQ-1500 | 1-2 t/h | 1500 mm | 7.5 kW | 1-4 mm | 1.6 t |
| SHQ-2000 | 2-3 t/h | 2000 mm | 11 kW | 1-4 mm | 2.2 t |
| SHQ-2500 | 3-4 t/h | 2500 mm | 15 kW | 2-5 mm | 3.1 t |
| SHQ-3000 | 4-6 t/h | 3000 mm | 18.5 kW | 2-5 mm | 4.0 t |
All four models run on 380V / 50Hz or a customized voltage, carry a 12 month warranty, and can be supplied with an SS304 pan for organic material with aggressive acidity. Quoted ball shape rate is 93 percent across the range, which keeps the fines recycle loop predictable when you size the screen and the recycle conveyor.
Two numbers link granulation to drying: granule size and discharge moisture. A pan type granulation plant that produces 1 to 4 mm balls at 30 to 40 percent moisture needs a dryer sized on water load, not on tonnage alone. If you buy a dryer matched to tonnage, you will run it hot, the surface of the granule will case-harden, and the core will still be wet when the bag is sealed. Size the dryer on kilograms of water per hour and keep the drum speed low enough that granules do not break against each other.
Screening is the second quality gate. Product, recycle and fines should be three separate streams, and the recycle conveyor should return fines to the mixer rather than directly to the pan, so moisture can be corrected before the next pass.
A pan type granulation plant is usually arranged as a single line with a return loop, because the recycle stream is the widest conveyor on site. Leave at least one metre of working space around the pan for scraper adjustment and water nozzle cleaning, and place the pan on a level concrete floor: an inclined pan transmits vibration, and an uneven base shows up as an oval granule within a week.
Zhengzhou Shenghong Heavy Industry has supplied fertilizer equipment since 2003, with ISO 9001, CE, SGS and BV certification available on the SHQ range. Standard lead time is 15 working days after deposit, supply ability is 80 sets per month, minimum order quantity is one set, and installation is supervised by our engineers on site. Whether you start with a single disc and grow into a full pan type granulation plant, the machine dimensions stay the same, so the second stage can be added to the same floor plan.
Send us your raw material type, target output in tons per hour and granule size range, and we will return a line configuration with equipment list within 12 hours.