logo

ZHENGZHOU SHENGHONG HEAVY INDUSTRY TECHNOLOGY CO., LTD. sales@gcfertilizergranulator.com 86--15286833220

ZHENGZHOU SHENGHONG HEAVY INDUSTRY TECHNOLOGY CO., LTD. Company Profile
blog
Home > blog >
Company news about Round Ball Fertilizer Making Line: How Round Granules Are Formed

Round Ball Fertilizer Making Line: How Round Granules Are Formed

2026-11-10
Latest company news about Round Ball Fertilizer Making Line: How Round Granules Are Formed

How a Round Ball Fertilizer Making Line Works

A round ball fertilizer making line turns powder into spherical granules that roll freely, flow well in a spreader and dissolve evenly in the field. The shape is not cosmetic. Round balls have less surface friction, so they screen better, coat more evenly and pack to a higher bulk density than irregular granules. In most plants the round shape is created in a pan granulator, where an inclined rotating disc rolls powder, water and binder into a ball, layer by layer.

This article explains the ball forming mechanism, the full line configuration, the settings that control roundness, and the checks that keep the ball shape rate high in daily production.

Ball Forming Mechanism on a Disc Pan

Ball growth on a pan follows three stages. First, fine powder is wetted and forms small nuclei. Second, the nuclei roll against the pan wall and pick up successive layers of moist powder, growing steadily. Third, when the ball reaches the discharge height set by the pan angle, it leaves the pan. Because growth is by layering rather than by pressing, the ball surface closes into a smooth sphere instead of a flake.

Roundness depends on four variables: pan angle, pan speed, moisture and binder. Change any one of them and the ball size distribution shifts. This is why an adjustable disc angle matters. The 45 to 55 degree range allows the operator to move between smaller, denser balls and larger, lighter balls without changing parts.

Line Configuration for a Round Ball Product

  • Feeding and crushing section: raw material is crushed and sieved to a fine powder so nuclei form uniformly.
  • Mixing section: horizontal or double shaft mixer blends powder, filler, binder and recycled fines.
  • Granulation section: one or more disc pan granulators with water spray and binder dosing.
  • Drying section: rotary dryer with hot air generator, sized to the granulator output.
  • Cooling section: rotary cooler to bring granules to ambient temperature before screening.
  • Screening section: rotary or vibrating screener separating finished, oversized and fine fractions.
  • Coating section: drum or chain coater for anti-caking powder and colour coating.
  • Packing section: automatic weighing, bag sewing and palletizing.

For capacity below 6 tons per hour, the standard arrangement is one pan granulator feeding one dryer. Above that, two or three pans feed a common dryer through a collecting belt, which is cheaper than building one very large pan and much easier to maintain.

Model Selection for Round Ball Output

ModelCapacityDisc diameterMotor powerTypical granule sizeTotal weight
SHQ-15001-2 t/h1500 mm7.5 kW1-4 mm1.6 t
SHQ-20002-3 t/h2000 mm11 kW1-4 mm2.2 t
SHQ-25003-4 t/h2500 mm15 kW2-5 mm3.1 t
SHQ-30004-6 t/h3000 mm18.5 kW2-5 mm4.0 t

All four models use the same adjustable disc angle of 45 to 55 degrees and reach a ball shape rate of 93 percent. The pan of the SHQ-3000 is SS304 stainless steel; the smaller models use a carbon steel pan with stainless steel available as an option for corrosive or high humidity material.

Settings That Control Roundness

Disc angle

Angle sets the residence time and the discharge height. Too steep and the material leaves before it rounds; too flat and the balls overgrow and stick together. Start near the middle of the 45 to 55 degree range, then adjust by half a degree at a time while watching the discharge.

Moisture

Feed moisture is typically 18 to 25 percent, and the pan adds water by mist spray. The correct feel is moist powder that clumps when squeezed but does not smear. Granules leave the pan at about 30 to 40 percent moisture and must be dried before bagging.

Binder

A binder improves nucleus strength and reduces fines. Dose it continuously and record the rate; changing binder rate without changing water is the most common cause of a sudden jump in oversized balls.

Recycle ratio

Screened fines returned to the pan act as ready-made nuclei and shorten the growth cycle. Keep the recycle steady, and the ball size distribution stays narrow; let it swing, and the screener load rises.

Daily Quality Checks

  • Sample the pan discharge every two hours and measure ball diameter with a gauge, not by eye.
  • Check the ball shape rate by counting deformed and broken balls in a 100 gram sample.
  • Record pan angle, spray water flow, binder rate and recycle tonnage on one sheet, every shift.
  • Inspect the discharge chute and pan rim for build-up; hardened material disturbs the rolling path.
  • Check dryer outlet moisture before packing, since wet balls deform in the bag and lose the round shape.
  • Verify screener mesh condition weekly; a torn mesh silently puts oversized balls into the product.
A 93 percent ball shape rate is measured on a settled process. If your line is below 90 percent, check spray pattern and recycle ratio before changing the pan angle.

Frequently Asked Questions

Can the same line make both round and irregular granules?

The pan granulator produces round balls by design. If you need irregular granules, the same preparation, drying, cooling and screening sections can be paired with a different granulator, so the investment in the rest of the line is not lost.

What raw materials can be used?

Fermented manure, compost, humus powder, blended NPK powder and similar materials in powder form. Fibrous organic material may need extra crushing and a higher binder dose.

What is the delivery time and minimum order?

Minimum order is one set, with about 15 working days lead time after deposit. Supply ability is around 80 sets per month, and machines are packed in export-grade wooden cases or loaded in containers.

Request a Line Proposal

Send us your raw material type, target tons per hour and the granule diameter you want to sell, and our engineers will confirm the pan model, motor power, dryer size and the complete layout within 24 hours. Shenghong Heavy Industry Technology Co., Ltd. has manufactured fertilizer equipment since 2003, holds ISO 9001 and CE, and serves customers in more than 60 countries.

Events
Contacts
Contacts: Miss. Judy
Fax: 86-371-64865777
Contact Now
Mail Us